8051 MICRO CONTROLLER TRAINER MODEL SM - 51 LCD*
SPECIFICATION :
80C31 / 80C51 / 80C51 Micro controller operating at 10MHZ
32KB powerful software monitor
256 bytes on chip RAM ( partially used by Firmware)
Two 16 bit Programmable Timer
32 Programmable I/O pins (24 from 8255 and 6 ( P1.0 to P 1.5) from Port 1 of 8051)
50 Pin FRC connector for system bus expansion
2@26 pin FRC connector for user interface from 8255
9 pin D type connector for RS 232C interface
Built in Power supply
Six different selectable baud rates from 150 to 9600
One timer and external interrupt
101 Pc type keyboard for entering user address / data and for commands
Built in line by line assembler ad disassembler
User - friendly software monitor for loading and executing programs with break point facility
Facility to connect to PC
-------------------------------------------------------------------------------------------------------------
8085 MICROPROCESSOR TRAINER MODEL SM - 85 LCD*
SPECIFICATION :
8085 Microprocessor operating at 6.144MHZ
16KB powerful software monitor
Three 16 bit Programmable Timer
48 Programmable I/O Lines
One RS 232C Serial interface ,terminated on a 9 pin D- Type Connector.
50 Pin FRC connector for system bus expansion
2@26 pin FRC connector for user interface, using 48 TTL I/O lines.
Six different selectable baud rates from 150 to 9600
One timer and external interrupt
101 Pc type keyboard for entering user address / data and for commands
Built in line by line assembler ad disassembler
User - friendly software monitor for loading and executing programs with break point facility
Facility to connect to PC
Built- in power supply
-------------------------------------------------------------------------------------------------------------
 
8086 MICROPROCESSOR TRAINER MODEL SM - 86 LCD*
SPECIFICATION :
8086 Microprocessor operating at 18.432MHZ
64K powerful software monitor
Three 16 bit Programmable Timer
48 Programmable I/O Lines using PPI
RS 232C Serial interface
50 Pin FRC connector for system bus expansion
2@26 pin FRC connector for user interface from 8255
9 pin D type connector for RS 232C interface
Six different selectable baud rates from 150 to 9600
One timer and external interrupt
101 Pc type keyboard for entering user address / data and for commands
Built in line by line assembler ad disassembler
User - friendly software monitor for loading and executing programs with break point facility and Including MASM Software
Facility to connect to PC
Built- in power supply
-------------------------------------------------------------------------------------------------------------
8 CHANNEL A to D CONVERTER MODULE MODEL - A1*
SPECIFICATION :
8 indipendent analog input channels.
0V to 5V analog input voltage range with single 5v supply
Easy to interface with all microprocessors.
No zeroadjust is required
Assembled in an elegant sloping cabinet.
Note : This experimental module can be interfaced to all Microprocessor trainers, Micro control trainers.
-------------------------------------------------------------------------------------------------------------
 
DIGITAL to ANALOG CONVERTER MODULE MODEL - A2*
SPECIFICATION :
One number ,8-Bit programmable digital to analog converter.
Buffered output
In unipolar mode output is 0-5V DC.
Assembled in an elegant sloping cabinet.
An external power supply of +or- 12V @ 250mA and +5V required
-------------------------------------------------------------------------------------------------------------
8251 & 8253 PROGRAMMABLE COMMUNICATION INTERFACE TRAINER MODEL - A3*
SPECIFICATION :
Synchronous and Asynchronous transmission.
Internal and external character synchronization
Generation of Synchronous baud rate generation
Full Duplex Transmitter and Receiver
All input outputs are TTL compatible.
Single TTL clock
-------------------------------------------------------------------------------------------------------------
 
8253 PROGRAMMABLE INTERVAL TIMER MODULE MODEL -A4
 
8253 is a programmable interval timer /counter.Timer applications in electronic instruments are very wide and important. 8253 has three timer / counters built -in one IC.Each timer can be indipendently programmed under 5 different modes.They are; interrupt on terminal count ( mode 0), programmable one shot (mode1), rate generator (mode 2), and square wave rate generator (mode 3), software triggered strobe (mode 4), and hardware triggered strobe. To experiment each of the above, we need clock input,gate control, and power supply. This trainer has all the necessary facilities, to experiment . Programs and listings are supplied.
Note: This experimental module can be interfaced to Microprocessor trainer SM-85 at system bus.
-------------------------------------------------------------------------------------------------------------
8255 EXPERIMENTAL MODULE MODEL - A5*
SPECIFICATION :
3@8bit Leds
8 bit buffer amplifiers.
Built-in Power supply
 
Note : This experimental module can be interfaced to all Microprocessor trainers, Micro control trainers.
-------------------------------------------------------------------------------------------------------------
 
8279 KEYBOARD DISPLAY INTERFACE MODEL -A6
SPECIFICATION :
16 robust keys are used.
Keys are arranged in 4x4 matrix
Status of keys are logged on an 8 BIT port
Programmable 8 bit LED port.
Requiers external power supply 5V DC @250mA
Note : This experimental module can be interfaced to all Microprocessor trainers, Micro control trainers.
-------------------------------------------------------------------------------------------------------------
 
 
 
Home | About us | Services | Calibration | Training program | Projects | Seminars | Careers | Inquiry | Clients | Lab Support | Contact Us
Copyrights 2012 @ All rights reserved by SM Micrro Systems. Design | designdreams.in